SATO GL408e / GL412e Instrukcja Operatora Strona 16
- Strona / 148
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Unit 3: Installation
GL408-412e Operator’s Manual
3-2
UNPACKING & PARTS IDENTIFICATION
Unpack the printer as directed in the following procedure.
1 Place the shipping container (box) upright on a soid, flat surface.
2 Open the box, remove any loose items and the first layer of packing material.
3 Carefully lift the printer and accessories from the box and place them on a solid flat surface.
4 Remove the plastic covers from the packed items and visually inspect for physical damage.
5 Ensure all components are present as dictated on the Packing List.
6 Report damaged property.
Figure 3-1, Unpacking & Parts Identification
Accessory Box
Printer
Shipping Container
Cushion
- GL4xxe Operator’s Manual 1
- PN: 9001163B 2
- TABLE OF CONTENTS 3
- INTRODUCTION 6
- ABOUT THIS MANUAL 7
- GENERAL DESCRIPTION 8
- CONTROL FEATURES 9
- TECHNICAL DATA 10
- Unit 2: Technical Data 11
- GL408-412e Operator’s Manual 11
- REGULATORY 12
- CHARACTER FONT CAPABILITIES 13
- BARCODE CAPABILTIES 14
- INSTALLATION 15
- Accessory Box 16
- Shipping Container 16
- PRINTER INSTALLATION 17
- MEDIA SELECTION 18
- MEDIA & RIBBON LOADING 18
- Figure 3-3c, Ribbon Loading 19
- CONTINUOUS MODE 20
- TEAR-OFF MODE 20
- CUTTER MODE 20
- DISPENSE MODE 20
- LINERLESS MODE 20
- LABEL PRINT DIRECTION 21
- INTERFACE SELECTION 22
- READY/BUSY INTERFACE SIGNALS 23
- SIGNAL SIGNAL DEFINITION 23
- READY/BUSY CABLE REQUIREMENTS 23
- IEEE1284 PARALLEL INTERFACE 24
- 1 To Host 32 Fault To Host 24
- 1 From Host 24
- UNIVERSAL SERIAL BUS (USB) 25
- 802.11G WIRELESS 26
- WIRELESS LAN SIGNAL STRENGTH 27
- SOFTWARE SPECIFICATIONS 27
- ALL INTERFACES 28
- STATUS5 TIMING CHARTS 29
- NORMAL PROCESS 29
- CANCEL PROCESS 29
- ERROR PROCESS 29
- PRINT PROCESS 30
- COMMAND PROCESS 30
- BCC ERROR PROCESS 30
- EXTERNAL SIGNAL 31
- 25-PIN CONNECTOR ASSIGNMENTS 32
- INPUT SIGNAL WAVE FORM 33
- START PRINTING 33
- REPRINTING 33
- OUTPUT SIGNAL WAVE FORM 34
- BASIC OPERATION 34
- PAPER END 34
- RIBBON END 34
- MACHINE ERROR 34
- Unit 3: Installation 35
- ACCESSORIES INSTALLATION 36
- CONFIGURATION 37
- PRINTER CONFIGURATION 38
- CONFIGURATION MODES 39
- CONFIGURATION MODE 40
- ADVANCED MODE 41
- SERIAL INTERFACE MODE 43
- PARALLEL INTERFACE MODE 44
- CENTRONICS INTERFACE MODE 45
- PGL EMULATION MODE 49
- ZGL EMULATION MODE 50
- DGL EMULATION MODE 51
- TGL EMULATION MODE 52
- IGL EMULATION MODE 53
- DIAGNOSTICS MODE 54
- PRINTER MANAGEMENT MODE 55
- DISPLAY INTENSITY ADJUSTMENT 56
- BUFFER CLEAR 56
- SOFT RESET 57
- KEY LOCK/UNLOCK 57
- INTERFACES 58
- USER MODE (TABLE 4-1) 59
- ADVANCED MODE (TABLE 4-3) 65
- Data Protocol 78
- Buffer Size in K 78
- EMULATION 98
- MENU DESCRIPTION 100
- IGL Setup 118
- Save state* 118
- Priority Setting 118
- Command* 118
- Error Log Clear 120
- TROUBLESHOOTING 125
- ERROR SIGNAL TROUBLESHOOTING 126
- DISPLAY EXPLANATION SOLUTION 127
- TROUBLESHOOTING TABLE 132
- NO PRINTED IMAGE 133
- INCORRECT LABEL POSITIONING 133
- SMEARED PRINT IMAGES 133
- INTERFACE TROUBLESHOOTING 134
- LAN ETHERNET INTERFACE 135
- 802.11G WIRELESS INTERFACE 135
- CENTRONICS INTERFACE 135
- HEX DUMP 136
- TEST LABEL PRINTING 136
- Figure 6-2, Sample Test Label 137
- MAINTENANCE 138
- CLEANING PROCEDURES 139
- PRINT HEAD REPLACEMENT 140
- FUSE REPLACEMENT 141
- Platen Roller Assy 142
- Retaining Bracket 142
- Lower Print Assy 142
- LABEL SENSOR POSITIONING 143
- PRINT HEAD BALANCE ADJUSTMENT 144
- PRINT HEAD PRESSURE 145
- PRINT HEAD ALIGNMENT 146
- RIBBON GUIDE ALIGNMENT 147
- RIBBON ROLLER ALIGNMENT 148
Powiązane produkty i podręczniki dla Drukarki etykiet SATO GL408e / GL412e
Drukarki etykiet SATO LT408 Instrukcja Obsługi
(115 strony)
(115 strony)
Drukarki etykiet SATO M8485S Instrukcja Operatora
(228 strony)
(228 strony)
Drukarki etykiet SATO CG212DT Instrukcja Obsługi
(109 strony)
(109 strony)
Drukarki etykiet SATO M-5900 Instrukcja Obsługi
(66 strony)
(66 strony)
Drukarki etykiet SATO /gt Series Instrukcja Obsługi
(106 strony)
(106 strony)
Drukarki etykiet SATO CL608 Instrukcja Obsługi
(245 strony)
(245 strony)
Drukarki etykiet SATO CG412 Dokumentacja
(100 strony)
(100 strony)
Drukarki etykiet SATO CL608 Dokumentacja
(58 strony)
(58 strony)
Drukarki etykiet SATO M-84PRO Dokumentacja
(52 strony)
(52 strony)
Drukarki etykiet SATO CL408e Dokumentacja
(10 strony)
(10 strony)
Drukarki etykiet SATO LM408e Dokumentacja
(86 strony)
(86 strony)
Drukarki etykiet SATO TH2 Instrukcja Użytkownika
(15 strony)
(15 strony)
Drukarki etykiet SATO M-8400 Instrukcja Operatora
(242 strony)
(242 strony)
Drukarki etykiet SATO M8485S Instrukcja Operatora
(107 strony)
(107 strony)
(87 strony)
Drukarki etykiet SATO S8424 Standard Dokumentacja
(142 strony)
(142 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji