SATO CL608VA Instrukcja Operatora Strona 80
- Strona / 256
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
COMMAND CODES
This section contains all the CL Series printer Command Codes. The commands must
be sent to the printer in an organized fashion in order for the label(s) to print.
The purpose of this section is to:
1. Explain the different commands and provide examples of their usage.
2. To provide a detailed reference for programming the CL Series Printers.
Each command begins on a separate page with its own heading. A uniform layout is
used to help you find key information about each command. For each Command
Code in this section, there will be a sample data input stream to the printer and the
expected print output. By studying the examples, you can learn how to use the
particular command within a whole block of printer code. Pay particular attention to
the “Special Notes” with each command to learn other important information.
The subject commands are highlighted in bold letters in the Reference Sheets. There
are two parts of most, but not all, commands. The first is the command character
which immediately follows the <ESC> code. It is always an upper case alpha or a
special character (such as an “&” or a “%”). It is never a lower case alpha character. If
the command requires additional variable information, it is represented by a group of
lower case alpha characters immediately following the command character. For
example, if an aaaabb is listed following the basic command, the printer will look
for six characters immediately following the command. The first four would represent
the value of aaaa and the next two the value of bb.
The maximum number of characters defined in a parameter is represented by the
number of characters shown in the command structure. For example, a command
followed by an aaaa can have up to four characters. In general, commands with only
one parameter following the command can be entered without the leading zeroes.
However, certain commands require the exact number of matching characters. A
command with two parameters listed following the command code without a comma
delimiter, such as aaaabbbb require the exact number of digits to be entered. If the
value of aaaa is “800” and the value of bbbb is “300”, then the parameters must be
entered as “08000300”. It is recommended that you make it a practice to always
enter leading zeros to prevent any mistakes.
NOTE: These examples assume the use of the Standard Protocol Command Codes,
a parallel interface and a 5 inch wide label in a CL408 printer. The labels for all other
printers will be similar, but, because of different resolutions and print widths may be
larger or scaled differently.
An alphabetical listing of the command codes is contained in Appendix A: Command
Code Quick Reference.
Section 4. Programming Reference
Page 4-109001035 Rev. ESATOCL SeriesPrinters
- CL Series 1
- Thermal Transfer Printers 1
- TABLE OF CONTENTS 5
- PRINTER OVERVIEW 11
- SECTION 1 11
- Section 1. Printer Overview 12
- CHARACTER FONTS 14
- BAR CODES 15
- PHYSICAL 16
- OPTIONAL ACCESSORIES 17
- SECTION 2 19
- SETTING UP THE PRINTER 21
- LINE LABEL RIBBON ERRORPOWER 30
- PITCHOFFSETPRINT 32
- REAR PANEL CL608 and CL612 34
- REAR PANEL CL408 and CL412 35
- SATO DEFAULT 42
- COMPLETED 42
- POWER ON 43
- Receive Buffer 43
- Hex Dump Label 43
- Print Buffer 43
- PRINT SPEED 45
- ADVANCED MODE 47
- VERT. OFFSET 48
- HOR. DIRECTION 48
- HOR. OFFSET 49
- GAP (X.XV) 50
- INPUT (X 50
- Label Only Eye Mark 51
- Less than 1.0V 2.5V to 3.5V 51
- CALENDAR ENABLED 52
- CALENDAR 52
- 01/01/01 01:01 52
- USER TEST PRINT 55
- LARGE SMALL 55
- PRINT SIZE 55
- to correctly position the 58
- Moved with 58
- Label Feed Direction 58
- SECTION 3 61
- CLEANING AND MAINTENANCE 61
- Sensors located beneath 65
- Label Hold-Down 65
- Assembly 65
- PROCEDURES CL408 and CL412 67
- Print Head 68
- Label Sensor Unit 70
- SECTION 4 71
- PROGRAMMING 71
- USING BASIC 72
- THE PRINT AREA 74
- Table 4.1, Print Area 75
- SATOSATO 78
- COMMAND DEFAULT SETTINGS 79
- COMMAND CODES 80
- Bar Codes 81
- Input to Printer <ESC>A 82
- Printer Output 83
- UCC-128 Without Incrementing 84
- With Incrementing 84
- Bar Codes, Expansion 86
- Bar Codes, Variable Ratio 87
- Base Reference Point 89
- Characters, Custom-Designed 91
- Character Expansion 93
- Character, Fixed Spacing 95
- Character Pitch 96
- <ESC>* 99
- Continuous Forms Printing 100
- Copy Image Area 101
- Cutter Command 103
- CL408 CL608 CL412 CL612 105
- Font, Vector 106
- Fonts WB, WL, XB & XL 108
- Form Feed 110
- Form Overlay, Recall 111
- Form Overlay, Store 112
- Graphics, Custom 113
- Graphics, PCX 115
- Job ID Store 116
- Journal Print 117
- Lines and Boxes 118
- Line Feed 120
- Mirror Image 122
- Mirrored Area 123
- Off-Line 124
- Print Darkness 126
- Print Length, Expanded 127
- Print Position 129
- Print Quantity 131
- Print Speed 132
- Repeat Label 133
- Replace Data (Partial Edit) 134
- Reverse Image 136
- Sequential Numbering 142
- <ESC>A 143
- <ESC>Q50 143
- <ESC>Z 143
- Start/Stop Label 144
- Calendar Option Commands 145
- Calendar Increment 146
- Calendar Print 148
- Calendar Set 150
- Memory Card Option Commands 151
- Memory Card Function 152
- Clear Card Memory 152
- Expand Memory Area 153
- Fonts, TrueType Recall 155
- Fonts, TrueType Store 156
- Format/Field Recall 157
- Format/Field Store 158
- Graphics, Custom Recall 159
- Graphics, Custom Store 160
- Graphics, PCX Recall 162
- Graphics, PCX Store 163
- Initialize 164
- Slot Select 165
- Custom Protocol Command Codes 167
- Download 167
- Two-Dimensional Symbols 169
- Two-Dimensional Bar Codes 170
- Data Matrix, Data Format 170
- Data Matrix, Print Data 172
- Maxicode 175
- SECTION 5 179
- INTERFACE SPECIFICATIONS 179
- THE RECEIVE BUFFER 180
- RS232C SERIAL INTERFACE 181
- RS232C Interface Signals 182
- Centronics interface 187
- (Not on CL408 or CL412) 188
- EXTERNAL OUTPUT SIGNAL TYPES 189
- SECTION 6 191
- TROUBLESHOOTING 191
- ERROR SIGNALS CL608 and CL612 194
- ERROR SIGNALS CL408 and CL412 195
- Section 6. Troubleshooting 196
- APPENDIX A 197
- COMMAND CODE QUICK REFERENCE 197
- CL408 CL412 CL608 CL612 201
- APPENDIX B 209
- BAR CODE SPECIFICATIONS 209
- <ESC>BD0bbcccd (data) d 210
- UPC-A/EAN-13 213
- ODD 024680 214
- EVEN 13579CD 214
- Industrial Two of Five 216
- Matrix Two of Five 217
- Code 128 218
- Example Without incrementing 224
- With incrementing 224
- Data Matrix 226
- Character Set 227
- CODE 128 CHARACTER TABLE 230
- Code 128 Character Table 231
- APPENDIX C 233
- CUSTOM GRAPHICS EXAMPLE 236
- PCX GRAPHICS EXAMPLE 240
- APPENDIX D 241
- LABEL CUTTER ALL MODELS 242
- CALENDAR ALL MODELS 249
- INTERFACE CARD ALL MODELS 249
- Appendix D: Optional Features 250
- APPENDIX E 251
- CUSTOM PROTOCOL COMMAND CODES 251
- ALT PROTOCOL 252
- DEFAULT COMPLETE 252
- USER DOWNLOAD 252
- APPENDIX F: 255
- LABEL WIZARD SUPPORT 255
Powiązane produkty i podręczniki dla Drukuj i skanuj SATO CL608VA
Drukuj i skanuj SATO XL410 Instrukcja Operatora
(225 strony)
(225 strony)
Drukuj i skanuj SATO TH208 Instrukcja Obsługi
(32 strony)
(32 strony)
Drukuj i skanuj SATO MB410i Instrukcja Obsługi
(86 strony)
(86 strony)
Drukuj i skanuj SATO GL4XXE Instrukcja Obsługi
(204 strony)
(204 strony)
Drukuj i skanuj SATO LM408e Instrukcja Obsługi
(98 strony)
(98 strony)
Drukuj i skanuj SATO CG4 Series Instrukcja Obsługi
(102 strony)
(102 strony)
Drukuj i skanuj SATO XL4xxe Instrukcja Użytkownika
(114 strony)
(114 strony)
Drukuj i skanuj SATO CL608 Dokumentacja
(12 strony)
(12 strony)
Drukuj i skanuj SATO TH208 Instrukcja Obsługi
(20 strony)
(20 strony)
Drukuj i skanuj SATO GY412 Instrukcja Obsługi
(217 strony)
(217 strony)
Drukuj i skanuj SATO XL400 Instrukcja Użytkownika
(194 strony)
(194 strony)
Drukuj i skanuj SATO M8485Se Instrukcja Obsługi
(216 strony)
(216 strony)
Drukuj i skanuj SATO CG412TT Instrukcja Użytkownika
(102 strony)
(102 strony)
Drukuj i skanuj SATO XL4xxe Instrukcja Użytkownika
(121 strony)
(121 strony)
Tii SVM-2 Series manuales
Manuales del propietario y guías del usuario para Equipo Tii SVM-2 Series.
Ofrecemos 1 manuales en pdf Tii SVM-2 Series para descargar gratis por tipos de documentos: Manual de usuario
Komentarze do niniejszej Instrukcji